HVAC Company North Branch MN | Why Isn’t My Furnace Working?

Introduction

I’ve been trying to get my furnace working for days. I’ve checked the pilot light, changed the filter, and reset the thermostat. Still nothing. What am I missing? HVAC Company North Branch MN

Check the thermostat, and that it’s set properly.

If you have a thermostat, it may be set incorrectly or not be functioning properly. To check the thermostat:

• Check that the temperature is set to AUTO.
• Check that the temperature is not stuck in one position (e.g., 73) and no longer moves with room temperature changes. If this is happening, call a professional to fix your furnace or air conditioner before trying anything else on your own!

Check your furnace filter and replace if necessary.

Check your furnace filter and replace if necessary.

• How often should you clean or replace it?
• What kind of filter should you use?
• How do you install the filter?

Check the pilot light on your gas furnace.

• Check the pilot light on your gas furnace.
• To light the pilot light, follow these steps:

Turn off the power to your furnace and open a window or door in order to ventilate the area. Then, locate the control panel for your furnace and follow these steps:

• Pull out the knob from its current position
• Push in on it as if you were turning it off then push it back in 3 times quickly 4) Wait for 30 seconds 5) Turn off all electricity at both ends of each wire

Check for blockages or debris in your air vents.

You can check for blockages or debris in your air vents by cleaning them with a vacuum. To do this, take off the vent covers and clean them with a brush attachment on your vacuum. While you’re at it, also remove any leaves or other debris from the outside of the vents.

Also check to see if there are any blockages in the vents by removing their covers and looking inside at each pipe opening using a flashlight if necessary (be sure not to touch anything). If needed, contact an HVAC Company North Branch MN to help check your air vents. True North Heating and Air can help check that your air vents are clear from blockages and debris.

Give the unit time to reset. HVAC Company North Branch MN

If your furnace is not working, don’t panic. You can try to reset it by following these steps:

• Wait a few minutes. The unit may be trying to start and needs time before it can engage again.
• Try turning the thermostat up or down (or switching it off and then back on). The air filters may need replacing or cleaning as well—if there are pets in the house that shed fur, this could contribute to clogging the filter and cause problems with heating systems!
• If none of this works, call an HVAC Company North Branch MN for help!

Check for power outages. HVAC Company North Branch MN

• Check for power outages in your area. Sometimes the power goes out for a few minutes or even an hour, and that can affect your furnace’s ability to run. You can check online or on your phone to see if there have been any reported outages in your area. If you do find that there was a power outage, you’ll want to report it so that when the power comes back on, it will work properly and not cause further problems with other devices in your home or apartment building.*
• Check if there are any lights on at the furnace itself—if so, then this could mean that the problem isn’t with the furnace but rather with something else (like another piece of equipment). If all of these things are off as well, then continue reading below!

There are a number of common problems that can cause furnaces to stop working, and a number of steps you can take to try and fix them on your own.

If your furnace isn’t working, there are a number of common problems that can cause the problem and a number of steps you can take to try and fix them on your own.

• Check the thermostat: The first thing you should do is check your thermostat and make sure it’s set to “on,” or at least not in cooling mode. This may seem obvious, but it’s easy to overlook if you aren’t paying attention.
• Check the filter: If the problem persists after checking the thermostat, look at whether or not a dirty air filter is causing it by taking out the old filter and holding it up against light. If there are noticeable dust bunnies clinging to its surface (or if it looks damp), replace this with a new one so that air can properly circulate through your home’s heating ducts when they’re heated up.
• Check pilot light: If this doesn’t work either, turn off power to everything except for one circuit breaker; then check if there’s an error message on any dashboard display screens by pressing buttons on each one until something happens onscreen (“error” messages will appear). If no error messages appear onscreen after pressing buttons for 20 seconds straight without interruption from yourself or anyone else who might be nearby during this time period (such as family members), go ahead and restart power again before proceeding further with troubleshooting steps because something else must be wrong with our system!

Conclusion

Hopefully, these tips have helped you get your furnace up and running again. If you’re still having trouble, don’t hesitate to call a professional! They’ll be able to tell you if something more serious is going on with your system and help you get it fixed quickly so that everyone stays warm during this cold winter season. True North Heating and Air is your local HVAC Company North Branch MN. We can help with all your HVAC needs. We want to be the trusted HVAC Company North Branch MN. Reach out to us to get on the schedule to get your furnace fixed so you can stay warm in these below zero temperatures. We look forward to helping you and being your HVAC Company North Branch MN.

 HVAC Company North Branch MN

HVAC Company North Branch MN

HVAC Company North Branch MN